May 19, 2024, 10:23:05 PM
Welcome,
Guest
Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Home
Garage
Forum
Help
Login
Register
GALLERY
Unread
Events
Birty Dastards Jeep Club
>
Forum
>
Tech Forum
>
Workshop
>
Topic:
Dana 30 ball joint
« previous
next »
Pages: [
1
]
Go Down
Print
Author
Topic: Dana 30 ball joint (Read 3065 times)
0 Members and 1 Guest are viewing this topic.
Richo
Forum Member
Guru: 0
Offline
Posts: 28
Vehicle: Cherokee 2.5TD 1999 & CJ7 1978 & Ford GPW 1944.
Year: 1999
Dana 30 ball joint
«
on:
April 30, 2023, 08:49:44 AM »
Hi All
Just some advice from anyone who has had to change the front axle ball joints on a Dana 30 axle on the XJs I had my mot yesterday and was given an advisory to replace the front top ball joints as they showed signs if wear.
I assume its best to change both upper and lower at the same time but i wanted to know from anybody whos done this job before if its worth the extra cost off buy aftermarket HD joints vrom the states or just sticking with the factory Dana or Spicer made joints available over here.
Any recommendations would be appreciated.
Ian
Logged
Dave69
Club Member
Forum Member
Guru: 15
Offline
Posts: 9457
Vehicle: CJ-7 4.2 auto
Year: 1979
Re: Dana 30 ball joint
«
Reply #1 on:
April 30, 2023, 11:31:22 AM »
not realy seen any difference with heavy duty and factory apart from fancy colours and cost. Most end up bring damaged in the same place if off roaded.
most of the time they end up sized in place and the heavy duty puller struggles. Heat is your friend along with a big hammer for help if the puller doesn't work
Logged
XJ 2.5 diesel - dead. XJ 4.0 6" lift - sold to some lucky person
CJ7 4.2 auto standard(ish)
Alfa 147 jtdm
wildwood
The 1 Tonne Kid
Marshal
Forum Member
Guru: 14
Offline
Posts: 5921
Re: Dana 30 ball joint
«
Reply #2 on:
April 30, 2023, 06:23:33 PM »
Did the ball joints on my Grand a few years back. Plenty of stuff on YouTube that I used to assist and take the guesswork out of the process.
Just replace with OEM stuff from Lighthouse, it’ll last for ages.
Logged
Richo
Forum Member
Guru: 0
Offline
Posts: 28
Vehicle: Cherokee 2.5TD 1999 & CJ7 1978 & Ford GPW 1944.
Year: 1999
Re: Dana 30 ball joint
«
Reply #3 on:
April 30, 2023, 07:40:35 PM »
Hi
Thanks for the input, i have changed ball joints on Dana 30 axles in the past so know they can be a challenge but i have enough gear to assist, just wasnt sure if it was worth spending more money on H/Duty joints or if it was a wasts of money.
I do like the idea of being able to grease them, dome font have nipples, not so keen on so called sealed for life parts. Will have a look on Ebay to see what I can find.
Cheers for your advice.
Logged
Print
Pages: [
1
]
Go Up
« previous
next »
Birty Dastards Jeep Club
>
Forum
>
Tech Forum
>
Workshop
>
Topic:
Dana 30 ball joint
Powered by
EzPortal
Go Up
Go Down