Birty Dastards Jeep Club

Tech Forum => Workshop => Topic started by: Anonymous on October 20, 2005, 07:13:16 PM

Title: JKS Quick disconnect help
Post by: Anonymous on October 20, 2005, 07:13:16 PM
I have a friend (cough)  :oops:
Title:
Post by: shep on October 20, 2005, 07:21:52 PM
hi Gaz

they are used on a TJ on the XJ you use the yellow bands to hold them out of the way when not connected

check out

http://jeepin.com/features/jks/index.asp (http://jeepin.com/features/jks/index.asp)
Title:
Post by: Mort on October 20, 2005, 07:27:59 PM
Even on a TJ they're not too smart, as they're prone to bending when you've got the discos parked on 'em if the tyres touch during articulation.  

I've removed mine and now use zip ties instead.
Title:
Post by: chrisjones on October 20, 2005, 07:53:31 PM
If you read the instructions Gaz, it tells you what they are!!!!! :shock:

On the XJ, they say to drill a hole in the side of the steering skid plate (if you've got one) and mount them there.

Have to say, it's a shit place for them.  both I and KD lost a retaining pin first time out cos the tyre hits them on full lock when it's stuffed into the arch!!!

I think I'm gonna junk mine and go the zip tie route. :wink:

BTW I now have a stock of 10 new retaining pins and suitable drill if you're interested.
Title:
Post by: Anonymous on October 20, 2005, 08:24:14 PM
Cheers guys, thats put my mind at rest, err I mean my friends  :wink:
Title:
Post by: Anonymous on October 20, 2005, 08:33:09 PM
What you do with them is.......


take the allen bolt in your left hand& the tube in your right, insert the allen bolt, insert into tube so that thread is sticking out of end.....

then grasp firmly between first finger & thumb of right hand (unless you are left handed), draw your arm right back........& chuck the bloody things over the nearest hedge!!!!!! :lol:
Title:
Post by: chrisjones on October 20, 2005, 08:41:25 PM
Yup!  that's about it! :lol:
Title:
Post by: Anonymous on October 20, 2005, 09:04:44 PM
Cheers your lordship, I, m sure "MY friend" will be glad to know it was something simple.

And thanks again for the piccy earlier  :wink:
Title:
Post by: monkeybiz on October 20, 2005, 10:12:57 PM
use BDS ones instead..... no need to tie them up as the whole center is removable
Title:
Post by: Anonymous on October 21, 2005, 08:52:04 AM
Same with my ones, but it's still a good idea to tie the roll bar up as that can drop right down and in a PITA when you bend the end :)
Title:
Post by: Mike Pavelin on October 21, 2005, 08:59:08 AM
Have the storage bits bolted to the steering skid on mine with no probs cos I'm running with 3 1/2 inch backspacing on the rims.
Title:
Post by: Anonymous on October 21, 2005, 09:17:06 AM
thats where i have mine bolted but the bloody things catch All the time on full lock & I have adjusted the bumpstops out a lot since i put the 31s on...........do ya reckon i could get away with some 32mm spacers & would that help???
Title:
Post by: Mike Pavelin on October 21, 2005, 09:57:13 AM
Yes but get billet ones, not cast ones. You will then find you need some minor trimming to clear the front flares as well. Fix one problem, create another. It's a Jeep thing.
Title:
Post by: Anonymous on October 21, 2005, 02:51:01 PM
Right, now where can I get some spacers from???? :?
Title:
Post by: chrisjones on October 21, 2005, 03:31:22 PM
Bronco do 60mm spacers for £168.50!!! 8)

Wheels with the correct offset for £2.86 more than spacers!! :?
Title:
Post by: 46stm on October 30, 2005, 08:34:22 PM
Going back to the beginning of this post, I made a load of stainless ones to replace the crap aluminium ones, worked perfect when I had a small 2" lift. Still got a few left if anyone wants some.

I now run a dia 1/2" stainless bar with holes in the end which sits in front of the rad grille on top, the disco's then slip over the ends of the rod and kept in place with the usual pins. Keeps the sway bar high up and out of the way, never seen anyone use anything like this but it works absolutely perfectly and is extremely positive.
Title:
Post by: Anonymous on October 30, 2005, 08:46:34 PM
Might take you up on that :wink:
Title:
Post by: Woody on October 30, 2005, 09:28:30 PM
Stew

you need the JKS style of disconnects for the gizmos Steve is talking, they wouldn't be any good for your sort of disconnect, sorry.

Woody
Title:
Post by: Anonymous on October 31, 2005, 08:41:22 AM
Thanks for the advice Woody