Birty Dastards Jeep Club

Tech Forum => Workshop => Topic started by: trent on August 04, 2005, 10:52:15 PM

Title: Bleeding clutch!
Post by: trent on August 04, 2005, 10:52:15 PM
Does anyone know if there's a certain method to bleeding the clutch?

I've been trying for nearly 2 hours and i'm still only getting a trickle coming out of the bleed nipple :cry:
Title:
Post by: Tank on August 04, 2005, 11:03:15 PM
Trent,dont know if its the same,but on some cars you cant bleed the brakes in the normal way and the answer usually is a pressure bleeder which screws over reservoir and connects to a tyre....Maybe its the same with your clutch so maybe worth a try,unless someone comes up with and easier solution. :idea:  :idea:
Title:
Post by: Anonymous on August 04, 2005, 11:09:12 PM
One for the Dr or Bubba maybe?
Title:
Post by: trent on August 04, 2005, 11:10:12 PM
I had read that pressure bleeding might be the answer, think i will look into that a bit more,   cheers Mike :wink:
Title:
Post by: Bubba on August 04, 2005, 11:14:04 PM
umm out of interest which slave cylinder do you have not that kin stoopid one in the bell housing i hope i personly prefer vacume bleeding and that is what i do if i have a prob
Title:
Post by: trent on August 05, 2005, 05:42:36 AM
Yep, internal slave!
Looks like vacuum/pressure bleed is definately the answer then!
Title:
Post by: Bubba on August 05, 2005, 07:15:15 AM
yup me to
Title:
Post by: Mik on August 07, 2005, 02:27:53 PM
Check that the bleed nipple on the clutch slave is clear of any blockage.
If the fluid finds it difficult to get out of the nipple then every press of the pedal will just actuate the clutch rather than bleed through the system.

I always removed the slave and clamped it up when fitting motorcycle clutch lines or you could easily spend a whole afternoon failing to bleed it properly.

Just a thought

HTH

Mik
Title:
Post by: trent on August 07, 2005, 10:11:37 PM
Mik, yes i been 'there' with the bikes before! :wink:

The problem i have now is that it's bled!!!!!!!!!! i think?........ no air coming out of the bleed nipple just pure fluid and i have a good clutch peddle......now the problem is i can't engage a gear with the engine running?????? it was ok before, so i know the gearbox is ok!
If i put it in gear before i start up(clutch depressed), and then start the engine,. it pulls as i lift the clutch and seems purfect, but if the engines running it just won't engage a gear..........could it need more bleeding?
Title:
Post by: Mike Pavelin on August 07, 2005, 10:23:54 PM
Hey, Trent, why were you bleeding the clutch in the first place? If it stopped working, you have a problem. They don't just suddenly get air in them.
Title:
Post by: trent on August 07, 2005, 10:36:18 PM
Mike, on the way back from ss the slave went, 'lost pedal pressure',, so i got a complete clutch kit fom the us, which included a the slave cylinder and replaced the whole lot,clutch inc the pilot!
After replacing it all it needed bleeding and thats when these problems began.
All in all it's been a royal PITA.
TBH, i feel like setting light to it :shock:
Title: Re: Bleeding clutch!
Post by: brian reid on July 27, 2011, 10:26:15 PM
does the pedal return to the up position or does it just hit the floor and stay there,reason i ask is i had something the same happen to me and it turned out to be the thrust bearing gone through the fly wheel,expencive fix.

we also had to replace the slave units around 2yrs ago,we bleed the system by just pumping the pedal,holding it down,person under the car open bleed screw,closed it,then foot was taken off pedal,then all repeated,took a while but we got there.

regards
Title: Re: Bleeding clutch!
Post by: brian reid on July 27, 2011, 10:27:55 PM
sorry thought it was an xj with external slave

sorry
Title: Re: Bleeding clutch!
Post by: The Smiths on July 27, 2011, 11:14:15 PM
He also had the issue 6 years ago :lol_hitting: :lol_hitting:
Title: Re: Bleeding clutch!
Post by: Bubba on July 28, 2011, 08:19:25 PM
the pos thrust goes well be fore the plate cutting the fingers off seen it lots of times
Title: Re: Bleeding clutch!
Post by: The Smiths on July 28, 2011, 08:44:33 PM
I've just had to do my thrust bearings, clutch plate is OK - as I stopped driving it when I got home - but could tell what it was when I got under to have a look....


(https://birtydastards.com/frm/proxy.php?request=http%3A%2F%2Fi219.photobucket.com%2Falbums%2Fcc124%2Fmds-houses%2Fjeep%2Fcherry%2F52fb75b3.jpg&hash=445e9a550883a306aa024447ee6c744e070a287d)

Had a spare in the garage:

(https://birtydastards.com/frm/proxy.php?request=http%3A%2F%2Fi219.photobucket.com%2Falbums%2Fcc124%2Fmds-houses%2Fjeep%2Fcherry%2Fabb9b555.jpg&hash=db9517764c8a567c2c7b6000e9278d3479242bf0)

Then changed it, only had to pull gearbox back far enough to change it:

(https://birtydastards.com/frm/proxy.php?request=http%3A%2F%2Fi219.photobucket.com%2Falbums%2Fcc124%2Fmds-houses%2Fjeep%2Fcherry%2Fdb37d9a7.jpg&hash=6e653865bdaae9afd5e2b0fdfa162dfca1483565)

Title: Re: Bleeding clutch!
Post by: Mike Pavelin on July 29, 2011, 01:19:55 PM
 :icon_eek:Holy tread revival, Batman!