Birty Dastards Jeep Club

Please login or register.

Login with username, password and session length
Advanced search  
Pages: [1]   Go Down

Author Topic: crank sensor,Too young to die  (Read 5927 times)

0 Members and 1 Guest are viewing this topic.

baldazacoot

  • Guest
crank sensor,Too young to die
« on: July 25, 2008, 01:30:47 PM »
93 YJ 4.0L Wrangler, 45k. I have suddenly aquired a dead engine. It has been starting and running exceptional with no problem.Now,Its decided not to start. Before owt else do I go for a CPS ??? Any Suppliers in Uk have 'em. Thanks      

:-)  :-)
Logged

baldazacoot

  • Guest
CPS
« Reply #1 on: July 25, 2008, 01:33:03 PM »
ELECTRICIAN HAS ADVISED THIS.
 Any second opinions?
Logged

Mike Pavelin

  • Guest
(No subject)
« Reply #2 on: July 25, 2008, 07:50:01 PM »
Have you checked for trouble codes?
Logged

baldazacoot

  • Guest
Codes?
« Reply #3 on: July 25, 2008, 09:04:39 PM »
Hi Mike,

Would i check the codes like it says on this website? or have you anything different to add to what it says?


http://www.jedi.com/obiwan/jeep/dtc.html
Logged

Bubba

  • "Cooter"
  • Marshal
  • Guru
  • *
  • Guru: 69
  • Offline Offline
  • Posts: 21029
(No subject)
« Reply #4 on: July 25, 2008, 09:06:56 PM »
is it an auto and does it turn over
Logged


trucks


shedric
cletus
mr whippy

I spent most of my money on alcohol, women and old  iron........ the rest of it I just wasted.

baldazacoot

  • Guest
(No subject)
« Reply #5 on: July 25, 2008, 09:13:08 PM »
Manual and yes it turns over. Had an electrician to look at it today but went away huffing and puffing with a recomendation of change the CKS c'os its cheaper than a proper electrician with all the tech stuff i would assume.
Logged

baldazacoot

  • Guest
(No subject)
« Reply #6 on: July 25, 2008, 09:49:14 PM »
NO lights on dash other than handbrake and seat belt.
 + no trouble codes showing,because of above???
:-?
Logged

Mike Pavelin

  • Guest
(No subject)
« Reply #7 on: July 25, 2008, 10:48:27 PM »
You should have a 'check engine' light as well. Cycle the ignition on off on off on and watch it flash a sequence of flashes and pauses starting 1flash pause 2flashes denoting code 12 for start of test and 5 pause 5 for code 55 end of test. anything in between these coses is a fault code.
Logged

baldazacoot

  • Guest
(No subject)
« Reply #8 on: July 25, 2008, 10:53:41 PM »
no lights on except handbrake and seatbelt. No check engine light!
Logged

Mike Pavelin

  • Guest
(No subject)
« Reply #9 on: July 26, 2008, 07:20:46 AM »
The Check Engine lamp should self test every time you turn the ignition on. It should be bottom left hand corner of the cluster of warning lamps. Better check the bulb. If it's ok the wiring to it or the Powertrain Control Module could be f***ed.
Logged

baldazacoot

  • Guest
(No subject)
« Reply #10 on: July 26, 2008, 09:21:35 PM »
Will check that out ASAIC, will let you know.
Logged

baldazacoot

  • Guest
(No subject)
« Reply #11 on: July 28, 2008, 11:17:59 PM »
Stripped all the dials out and checked the wiring out as far as going into harness, seems ok???  Still no check engine light on, bulb ok.
Logged
Pages: [1]   Go Up
« previous next »
 
Powered by EzPortal