Birty Dastards Jeep Club

Please login or register.

Login with username, password and session length
Advanced search  
Pages: [1]   Go Down

Author Topic: 2000 TJ engine install into 97-99 TJ  (Read 5309 times)

0 Members and 1 Guest are viewing this topic.

Asylum

  • Marshal
  • Forum Member
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 702
2000 TJ engine install into 97-99 TJ
« on: October 29, 2006, 10:46:54 AM »
Can anybody tell me if this is possible?

I ask because I noticed the manifold/header is different, but asume that if the 2000 spec down pipes were purchased it would fit?

Are there any other problems?

The story is. A guy was selling one on Ebay. I emailed him. Turned out he bought it from a guy from J33P who bought a engine/gearbox combination and only needed the gearbox. So he sold the engine on. The guy who bought it wanted it for his 98 TJ left hand drive. Discovered it would not fit because of the mounting points.

Would that be the same problem for a right hand drive?

I figured it would be very handy to have a complete engine with water pump, alternator etc in storage for spares or repairs or replacement considering its low mileage and good condition and cheap price.

Cheers
Clayt
 :D
Logged
Aut viam inveniam aut faciam

ponyracer1

  • Guest
(No subject)
« Reply #1 on: October 29, 2006, 05:35:01 PM »
Sounds like it would be a good buy if you can get it cheap. The guy that couldn't make it fits sounds like a prat, as far as I've seen the 4.0 block is nearly the same from 87 to 04. The only changes were coil on plug instead of a distributor and when they went to the HO from the renix computer system.
Logged

Mike Pavelin

  • Guest
(No subject)
« Reply #2 on: October 30, 2006, 07:16:03 AM »
There's no reason a RHD motor won't fit a LHD. Only the position of the alternator and AC compressor are changed to clear the steering gear. The problem on a 2000 is that it has distributorless ignition, coil on plug coils, different wiring, manifolds and plumbing which mean that you have to swap all the '97 ancillaries over. Fitting a '97 into a 2000 would be more of a problem as the earlier head won't take the triple coil pack as it doesn't have the mountings in the casting.

I have a 2000 WJ block in my '91 XJ. The mounting points are all the same and all the '91 parts fit it.
Logged

Mike Pavelin

  • Guest
(No subject)
« Reply #3 on: October 30, 2006, 06:19:11 PM »
Apparently you mayl need the 2000 M/Y motor mounts.
Logged

Asylum

  • Marshal
  • Forum Member
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 702
(No subject)
« Reply #4 on: October 30, 2006, 08:35:23 PM »
Thanks for your help guys.

It sounds a lot of work to swap the engine should I wish to and more like there are fewer parts that are interchangeable than I thought. So I would not have the spares I thought I would be gaining.

The guy has told me I can have it for £400 and its up to me to arrange collection.

Do you guys think it would be worth the money taking all the above into consideration?

Mike, I am afraid I am not that knowledgeable regarding parts. Sorry about my ignorance but what is a M/Y 2000 motor mount? Are they hard to find and would it require any fabbing to install?

Cheers
Clayt
 :D
Logged
Aut viam inveniam aut faciam

Asylum

  • Marshal
  • Forum Member
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 702
(No subject)
« Reply #5 on: November 01, 2006, 11:13:37 PM »
I am in 2 minds over this engine and so am wondering if there is anybody that actually needs one? It seems more complicated than I had thought to use for spares or replacement, but if anybody would like the guys email to come to an arrangement in the mean time, then pm me and I will pass it on.

Clayt
 8)
Logged
Aut viam inveniam aut faciam

Woody

  • Guest
(No subject)
« Reply #6 on: November 04, 2006, 12:02:37 AM »
As Mike said the motor mounts are probably different.  I helped drop a 2000+ engine into a 98 TJ and we couldn't get the motor mounts from the original engine to fit onto the block.  We sourced some from an 02 TJ that had been written off, if you can't find any at a scrappy you should be able to order then from your local stealership.

It is a simple nut and bolt job, no fabricating required.
Logged

Tragic

  • Guru
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 843
  • Vehicle: A proper Jeep!
  • Year: 1993
(No subject)
« Reply #7 on: November 04, 2006, 07:35:23 PM »
If this engine is the one I'm thinking of, it was swapped out for a 4.7 supercharged stroker lump and NV3550, until then it was serviced and looked after regardless of cost. If you need an engine, this is a good one!
Logged

isle of man

  • بعض العضو التناسلي النسوي...
  • Club Member
  • Forum Member
  • *
  • Guru: 6
  • Offline Offline
  • Posts: 11537
  • Vehicle: G-Class AKA “The G spot”
  • Take the road less travelled...
    • http://www.4x4.im
(No subject)
« Reply #8 on: November 04, 2006, 10:07:37 PM »
Quote from: "Tragic"
If this engine is the one I'm thinking of, it was swapped out for a 4.7 supercharged stroker lump and NV3550, until then it was serviced and looked after regardless of cost. If you need an engine, this is a good one!



owwwwwww looks like one of mark gassers...........



peter henry
Logged
"Not all those who wander are lost"

Tragic

  • Guru
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 843
  • Vehicle: A proper Jeep!
  • Year: 1993
(No subject)
« Reply #9 on: November 05, 2006, 05:05:03 PM »
Quote from: "isle of man"

owwwwwww looks like one of mark gassers...........



peter henry


Yup. The owner (not Gasser) offered me the engine and box about 18 months ago for £1400. Probably worth it at the time but way out of my league!
Logged

Asylum

  • Marshal
  • Forum Member
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 702
(No subject)
« Reply #10 on: November 07, 2006, 11:44:06 AM »
The engine is on ebay if anybody would like to bid.

http://cgi.ebay.co.uk/2000-Jeep-Wrangle ... dZViewItem

 8)
Logged
Aut viam inveniam aut faciam
Pages: [1]   Go Up
« previous next »
 
Powered by EzPortal