Topic: Froadin' for the first time with JKS discos... (Read 14572 times)

lefty · « **on:** June 17, 2006, 05:02:34 PM »

Wow, what an amazing difference!

Was at a BORDC novice competition and came joint second from 9 entrants - all 8 other were defenders and discos, mostly modified to some extent.

Have done a bit of damage though. The passenger-side bracket that the bottom of the dis-connect attaches to bent - no idea how I managed that! Had to drive home with that disco cable-tied to the anti-roll bar and I'll take the wheel off tonight and try to hammer it back into place.

Second thing (and this is a recurring problem) is that my bottom leaf springs keep rotating slightly around the centre point where the u-bolts are. This means the rear end of the leaf can touch the tyre! I've tried tightening the u-bolts but I've obviously not tightened them enough, Anyone else experienced this?

Cutting off the rear ant-roll bar has also made a big difference. If anyone with an xj hasn't done it I can highly recommend it. I reckon it's actually improved the road handling of my xj

I was getting a bit of ribbing for turning up in a non-landie today but managed a few solihull scalps... One particularly tricky bit that foiled 3x discoveries, a 90 and a 110 was no problem at all for Jolly Green - I just sailed through :lol: :lol:

trent · « **Reply #1 on:** June 17, 2006, 05:08:28 PM »

Nice one!
Sounds like you had fun

lefty · « **Reply #2 on:** June 17, 2006, 05:12:56 PM »

T'be sure. :lol:

Tank · « **Reply #3 on:** June 17, 2006, 06:12:56 PM »

Well done Lefty.......hope you get the minor damage sorted without too much trouble
Its suprising what the XJ`s can do.Mine was phenominal off road as a few others will tell you.Wished i could have kept it but unlike some of the other more affluent members,i could only afford one jeep and decided on keeping the CJ.Thats getting there though,thanks to help from other members

lefty · « **Reply #4 on:** June 17, 2006, 08:27:50 PM »

I did wonder about doing that actually, what's it handle like on the road while disconnected?? :shock:

Bat Fastard · « **Reply #5 on:** June 17, 2006, 09:42:20 PM »

I left my TJ disconnected for weeks, and yes it did lean a bit but you get used to it.

I would not like to leave it disconnected if it was my daily ride, but going to and from off road sites it was ok.

Anonymous · « **Reply #6 on:** June 17, 2006, 09:49:40 PM »

Im about to as well (Leave it disco'd that is)

monkeybiz · « **Reply #7 on:** June 17, 2006, 09:50:43 PM »

sounds like you need new hendricks clamps for your rear leafs............. pro comp do cheap ones

trent · « **Reply #8 on:** June 17, 2006, 10:34:47 PM »

Here ya go http://www.bds-suspension.com/products/ ... clamps.php

monkeybiz · « **Reply #9 on:** June 17, 2006, 10:38:32 PM »

thanks for that i didnt want to post my own products

trent · « **Reply #10 on:** June 17, 2006, 10:42:57 PM »

There you go Lefty :shock:

trent · « **Reply #11 on:** June 17, 2006, 10:48:40 PM »

Quote from: "xj.jeeper"

OK,
Now for the most dumb ass question of the day ........ What they for / what they do ?

It's not a dumb ass question! :wink:

If you look at your rear leaf spring pack, you'll have something similar near the ends! These ones can be fitted further down the spring pack (nearer the axle) to stop the shorter leafs pushing out sideways..........does that make sense?

lefty · « **Reply #12 on:** June 18, 2006, 09:33:01 AM »

Exactly what I need mate! I bodged something v similar with jubilee clips to get me home yesterday

chrisjones · « **Reply #13 on:** June 18, 2006, 07:54:36 PM »

My Skyjacker springs did exactly the same thing. The helper leaves kept turning round. Fitted some of them there clamp things and problem solved.

Just fit them as close to the axle as you can so that the helper leaf don't stop the spring from drooping properly. :wink:

lefty · « **Reply #14 on:** June 18, 2006, 09:06:26 PM »

Thanks for the advice mate, next thing on the list... :wink:

lefty · « **Reply #15 on:** June 20, 2006, 01:09:54 PM »

I've decided to make my own, got some 2" bar and am going to bend it and weld it to the bottom leaf. Anyone else tried this??

I know the clamps aren't exactly dear but my father-in-law's got a welder sitting in his garage and I want to play with it :twisted:

tim_aka_tim · « **Reply #16 on:** June 20, 2006, 02:28:32 PM »

Quote from: "lefty"

I've decided to make my own, got some 2" bar and am going to bend it and weld it to the bottom leaf. Anyone else tried this??

No, but springs are made from hardened steel, not mild steel. I think someone may know better, but I'd guess you'll most likely just make a mess and ruin the spring.

lefty · « **Reply #17 on:** June 20, 2006, 02:34:00 PM »

Wow, you must know me pretty well... :lol:

chrisjones · « **Reply #18 on:** June 20, 2006, 02:38:11 PM »

What ever you do DON'T weld to the spring!!!

They're made of spring steel which is given it's properties by heat treating.
The heat from the welder will f**k them.

All you need is a bit of steel strip about 3/4 of an inch wide. Fold it into shape around the spring so that there is a couple of tabs at the top that you can drill and stick a bolt through. It don't need to be heavy duty, :wink:

lefty · « **Reply #19 on:** June 20, 2006, 05:35:48 PM »

:oops:

Author Topic: Froadin' for the first time with JKS discos... (Read 14572 times)

lefty

lefty

Tank

lefty

Bat Fastard

Anonymous

monkeybiz

monkeybiz

lefty

lefty

lefty

lefty

lefty