Birty Dastards Jeep Club

Please login or register.

Login with username, password and session length
Advanced search  
Pages: 1 [2]   Go Down

Author Topic: TJ Front drive Shafts  (Read 9147 times)

0 Members and 1 Guest are viewing this topic.

MOCAJ

  • Club Member
  • Forum Member
  • *
  • Guru: 4
  • Offline Offline
  • Posts: 6366
(No subject)
« Reply #25 on: December 09, 2008, 07:13:32 PM »
bubba, doctor death is barry the MOT man

Mick is the repair man  :wink:
Logged
short term jeep owner since 2005, every truck is a never ending project. Birtys, the best club in Jeepland

Dave69

  • Club Member
  • Forum Member
  • *
  • Guru: 15
  • Offline Offline
  • Posts: 9457
  • Vehicle: CJ-7 4.2 auto
  • Year: 1979
(No subject)
« Reply #26 on: December 09, 2008, 07:16:14 PM »
Quote from: "V8 Bubba"
so how did doctor death conclude the ujs were welded in


probably caked in old grease etc and he couldn't be bothered to clean them off for inspection
Logged
XJ 2.5 diesel - dead. XJ 4.0 6" lift - sold to some lucky person
CJ7 4.2 auto standard(ish)
Alfa 147 jtdm

Bubba

  • "Cooter"
  • Marshal
  • Guru
  • *
  • Guru: 69
  • Offline Offline
  • Posts: 21029
(No subject)
« Reply #27 on: December 09, 2008, 07:19:28 PM »
the noise if our suspicions are correct is not realy from the ujs though they may be worn it is from the ball coupling of the constant velocity bit it dries and sqweaks like chirping bird it is greased on assembly and does not have a greaser on it but there is a rubber boot on the coupling that you can peel very slightly back and then get a needle fitting in to it and then grease it this normaly if cought in time saves a rebuild for quite a while ......we did this to the bishops tj though not sqweeking it had started to get stiff and notchy
Logged


trucks


shedric
cletus
mr whippy

I spent most of my money on alcohol, women and old  iron........ the rest of it I just wasted.

MM

  • Guest
(No subject)
« Reply #28 on: December 09, 2008, 07:35:29 PM »
Quote from: "V8 Bubba"
we did this to the bishop, though not sqweeking it had started to get stiff and notchy


yeah, so I had heard :twisted:  :twisted:
Logged

PtP

  • Club Member
  • Guru
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 872
  • Stourbridge, West Midlands
(No subject)
« Reply #29 on: December 09, 2008, 08:17:35 PM »
This is the rubber boot Bubba is talking about






The new ones from lighthouse don’t have the rubber boot on them.



Logged
Peter

Bubba

  • "Cooter"
  • Marshal
  • Guru
  • *
  • Guru: 69
  • Offline Offline
  • Posts: 21029
(No subject)
« Reply #30 on: December 09, 2008, 08:31:21 PM »
no but it has got a needle greaser fitting
Logged


trucks


shedric
cletus
mr whippy

I spent most of my money on alcohol, women and old  iron........ the rest of it I just wasted.

gazjeep

  • Marshal
  • Forum Member
  • *
  • Guru: 9
  • Offline Offline
  • Posts: 7280
  • Vehicle: TJ - Der Panzer - CBR
(No subject)
« Reply #31 on: December 09, 2008, 08:40:52 PM »
This info maybe no news to some but trust me, show me a pic & tell it like it is & I catch on pretty quick  :wink:
Logged
Taking ya girl to heaven & back

isle of man

  • بعض العضو التناسلي النسوي...
  • Club Member
  • Forum Member
  • *
  • Guru: 6
  • Offline Offline
  • Posts: 11537
  • Vehicle: G-Class AKA “The G spot”
  • Take the road less travelled...
    • http://www.4x4.im
(No subject)
« Reply #32 on: December 10, 2008, 12:36:09 AM »
net-a-porter by chance?
Logged
"Not all those who wander are lost"

MM

  • Guest
(No subject)
« Reply #33 on: December 10, 2008, 06:48:54 AM »
bed-a-porter :wink:  :wink:  :wink:  :wink:  :wink:




(super kingsize too!!!!)
Logged

The Smiths

  • Forum Member
  • *
  • Guru: 1
  • Offline Offline
  • Posts: 1084
(No subject)
« Reply #34 on: December 10, 2008, 09:40:42 AM »
My ball coupling was doing this, needed to get it sorted and no time (or money) to wait for a new one.

Stripped it down, regreased around the roller bearings (making sure they all went back in) and repacked with grease - and it has done 10,000 miles since without any problem.

Cost = £0, time about 2 hours (which would have been same fitting new parts)

Probably all depends how far gone the rollers are though.
Logged
If you always do what you have always done You will always get what you have always got
Please give to our Mac4x4 fund: http://www.justgiving.com/The-Smiths-2015

daggie

  • Moderator
  • Forum Member
  • *
  • Guru: 3
  • Offline Offline
  • Posts: 3447
(No subject)
« Reply #35 on: December 10, 2008, 04:16:11 PM »
Gaz and spanners.............................................................










































 :mrgreen:
Logged
Grand cherry, 3.0 crd Overland
Grand cherry, 2.7 crd
95, Cherry, aka Blackie      P38 range rover

Bubba

  • "Cooter"
  • Marshal
  • Guru
  • *
  • Guru: 69
  • Offline Offline
  • Posts: 21029
(No subject)
« Reply #36 on: December 10, 2008, 04:29:30 PM »
stew could help him ROFL  ROFL  ROFL  ROFL  ROFL  ROFL
Logged


trucks


shedric
cletus
mr whippy

I spent most of my money on alcohol, women and old  iron........ the rest of it I just wasted.

gazjeep

  • Marshal
  • Forum Member
  • *
  • Guru: 9
  • Offline Offline
  • Posts: 7280
  • Vehicle: TJ - Der Panzer - CBR
(No subject)
« Reply #37 on: December 10, 2008, 06:01:55 PM »
Well the wife hasn't stopped laffing for 5 minutes now  8-), never pretended to be a hero with the spanners, never been taught about mechanicals  :shock:  :lol:  :lol:
Logged
Taking ya girl to heaven & back

Bubba

  • "Cooter"
  • Marshal
  • Guru
  • *
  • Guru: 69
  • Offline Offline
  • Posts: 21029
(No subject)
« Reply #38 on: December 10, 2008, 06:47:27 PM »
i am a complete retard but i get by
Logged


trucks


shedric
cletus
mr whippy

I spent most of my money on alcohol, women and old  iron........ the rest of it I just wasted.

gazjeep

  • Marshal
  • Forum Member
  • *
  • Guru: 9
  • Offline Offline
  • Posts: 7280
  • Vehicle: TJ - Der Panzer - CBR
(No subject)
« Reply #39 on: December 10, 2008, 06:58:15 PM »
Quote from: "V8 Bubba"
i am a complete retard but i get by


& I have got ginger hair too (whats left of it) & like you Bubs somehow have got by this far  :lol:  :wink:
Logged
Taking ya girl to heaven & back

scrw

  • Guest
(No subject)
« Reply #40 on: December 10, 2008, 07:01:08 PM »
stew will bring his tool kit along :lol:
Logged

gazjeep

  • Marshal
  • Forum Member
  • *
  • Guru: 9
  • Offline Offline
  • Posts: 7280
  • Vehicle: TJ - Der Panzer - CBR
(No subject)
« Reply #41 on: December 10, 2008, 07:05:33 PM »
I'll bring me sun glasses for the glare then  :lol:
Logged
Taking ya girl to heaven & back

Panic mechanic!

  • Guest
(No subject)
« Reply #42 on: December 10, 2008, 07:41:09 PM »
cool I have never seen a unused toolkit before, shall i bring a camera?
Logged

scrw

  • Guest
(No subject)
« Reply #43 on: December 10, 2008, 08:45:44 PM »
don't use the flash though, it will blind everyone  :lol:
Logged

isle of man

  • بعض العضو التناسلي النسوي...
  • Club Member
  • Forum Member
  • *
  • Guru: 6
  • Offline Offline
  • Posts: 11537
  • Vehicle: G-Class AKA “The G spot”
  • Take the road less travelled...
    • http://www.4x4.im
(No subject)
« Reply #44 on: December 10, 2008, 08:53:14 PM »
Quote from: "MM"
bed-a-porter :wink:  :wink:  :wink:  :wink:  :wink:




(super kingsize too!!!!)


Talk is cheap you little dogger!!!!!!!!!

Any photos to substantiate such a phenonimum?
Logged
"Not all those who wander are lost"

Bishops Finger

  • Guest
(No subject)
« Reply #45 on: December 10, 2008, 09:40:48 PM »
Gaz..sure the experts will sort the issue out

If any of the no longer shiny tool kit or owt I can bring down on sunday are needed....please let me know :wink:
Logged

MM

  • Guest
(No subject)
« Reply #46 on: December 11, 2008, 07:34:01 AM »
Quote from: "isle of man"
Quote from: "MM"
bed-a-porter :wink:  :wink:  :wink:  :wink:  :wink:  :wink:
Logged
Pages: 1 [2]   Go Up
« previous next »
 
Powered by EzPortal