Birty Dastards Jeep Club

Please login or register.

Login with username, password and session length
Advanced search  
Pages: [1]   Go Down

Author Topic: Tube fenders  (Read 1279 times)

0 Members and 1 Guest are viewing this topic.

wildwood

  • The 1 Tonne Kid
  • Marshal
  • Forum Member
  • *
  • Guru: 14
  • Offline Offline
  • Posts: 5921
Tube fenders
« on: November 01, 2011, 03:13:17 PM »
Just about to order some steel for the 1 Tons fender requirements.......................

But being a joiner I'm still confused by 'gauge stuff'.................

When I did my traction bar and side steps the wall thickness was about 3mm on 1 3/4" ERW

Apparently (googled a chart on this) 12gauge is 2.7mm

So for fenders I am using 1 1/4" ERW and gauge wise.??????????????????????

12g       = 2.7mm
14g       =1.94mm
16g       =1.55mm

They got to be strong but not bomb proof.............. also I am using a pipe bender Mau Mart stylee not a full blown tube bender from JD2 (I wish)

otherwise known as the 'kink master' If there are a few ripples they will be covered by the sheet steel. so no worries there.

Gut reaction say 14g.................. All advice very welcome................... in the dark here :icon_twisted:
Logged

Bulldog67

  • Arthur Daley: Graduated
  • Guru
  • *
  • Guru: -936
  • Offline Offline
  • Posts: 25395
  • Vehicle: Man Sized Old Iron
  • Anti Colour Truck Mafia - I'm The Fuckin Daddy
Re: Tube fenders
« Reply #1 on: November 01, 2011, 03:18:49 PM »
before the queue starts forming  i would like it acknowledged that im here first
Logged
Bulldog's 22+ trucks: http://www.birtydastards.com/frm/index.php?topic=20288.0 :025:                                   :headbanger: 401 Dog * 401 Molotov :headbanger:  
Civilise the mind but make savage the body  :027:           Im only responsible for my karma :059:

Nosebolt

  • Guest
Re: Tube fenders
« Reply #2 on: November 01, 2011, 04:58:53 PM »
when I made Tonkas tube fenders I used 50mm x 4mm seamed tube, 2 options if you want to limit the 'ripples' 1st is fill the tube with wet sand and plug the ends, also seen it done with ball bearings but hard to get out, ok if only doing one or two bends, 2nd is to make some forms, square bar with a u shape milled length ways to replace the small rollers either side of the push form.
Logged

IrishCJ6

  • Guru
  • *
  • Guru: 3
  • Offline Offline
  • Posts: 1033
Re: Tube fenders
« Reply #3 on: November 01, 2011, 07:50:20 PM »
You will struggle to form any sort of bend using a standard bender under 3mm, when I do my rollcage I will be using the wet sand method and 2.5mm wall thickness as I too would love a JD2 bender but can not justify buying one.
Logged

isle of man

  • بعض العضو التناسلي النسوي...
  • Club Member
  • Forum Member
  • *
  • Guru: 6
  • Offline Offline
  • Posts: 11536
  • Vehicle: G-Class AKA “The G spot”
  • Take the road less travelled...
    • http://www.4x4.im
Re: Tube fenders
« Reply #4 on: November 01, 2011, 08:15:09 PM »
Logged
"Not all those who wander are lost"

greggmo

  • Founder
  • Forum Member
  • *
  • Guru: 2
  • Offline Offline
  • Posts: 8230
Re: Tube fenders
« Reply #5 on: November 07, 2011, 05:25:10 PM »
48.8 x 3 is about right and it wont break the bank. plenty srtong as the dumb ass who reversed into mine last week found out :hysterical:
Logged

wildwood

  • The 1 Tonne Kid
  • Marshal
  • Forum Member
  • *
  • Guru: 14
  • Offline Offline
  • Posts: 5921
Re: Tube fenders
« Reply #6 on: November 07, 2011, 08:08:42 PM »
nice one Greggmo.......
Bit the bullet today and ordered some 1 1/4 tube, a 6.1 metre length!!! Its 10g so I guess thats 3mm or near as .120 spec that used to be.... gonna be doing the wet sand trick for bending..

Also 1  sheet of 1.2mm and  1 sheet of 2.5mm.  1m x 2.5m for bodywork........ wing tops and stuff..........

Bundlebox delivered on Friday........ new carrier for the 14 bolt and lockright for the front dana 60. Started diff cover removal and oil drain on the front dana 60 tonight.

Also retrained myself on the fantasy build and DIDN'T buy the caddy 500 and th400 for £511..... guess I'll live to regret that :jpshakehead:

Apart from that just trying to avoid S.......A..........D.......... that is biting me in the ass as usual :die:
Logged

Warthog

  • Bla, bla, bla....
  • Forum Member
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 1279
  • Proper Job!
Re: Tube fenders
« Reply #7 on: November 07, 2011, 08:42:01 PM »
I have a set ready to fit :003:



If you want them Jez?

Generally, to prevent ripples. Pack with sand and seal ends. Make sure the sand is well packed.
Logged

wildwood

  • The 1 Tonne Kid
  • Marshal
  • Forum Member
  • *
  • Guru: 14
  • Offline Offline
  • Posts: 5921
Re: Tube fenders
« Reply #8 on: November 07, 2011, 10:31:07 PM »
Ooh errr Missus................ A tube fender set for a YJ Mark??? And you a L***d R***r person???

Seriously tempted almost and then I realized that I have the 'high fender trick' so don't think would work.............  Seem to remember Double J got a set of YJ tube fenders to work on his TJ .....maybe a set for Asylum then???
Logged

Warthog

  • Bla, bla, bla....
  • Forum Member
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 1279
  • Proper Job!
Re: Tube fenders
« Reply #9 on: November 08, 2011, 03:07:24 AM »
Quote from: wildwood on November 07, 2011, 10:31:07 PM
Ooh errr Missus................ A tube fender set for a YJ Mark??? And you a L***d R***r person???

What can i say?....I collect stuff/crap :003:

Yup they be the one JJ had :icon_winkle:
Logged

Bulldog67

  • Arthur Daley: Graduated
  • Guru
  • *
  • Guru: -936
  • Offline Offline
  • Posts: 25395
  • Vehicle: Man Sized Old Iron
  • Anti Colour Truck Mafia - I'm The Fuckin Daddy
Re: Tube fenders
« Reply #10 on: November 08, 2011, 05:05:07 AM »
can they be shoehorned onto a CJ?
Logged
Bulldog's 22+ trucks: http://www.birtydastards.com/frm/index.php?topic=20288.0 :025:                                   :headbanger: 401 Dog * 401 Molotov :headbanger:  
Civilise the mind but make savage the body  :027:           Im only responsible for my karma :059:

willo

  • Guru
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 3699
  • Vehicle: CJ7
  • Year: 1982
Re: Tube fenders
« Reply #11 on: November 08, 2011, 08:08:08 AM »
Quote from: Warthog on November 08, 2011, 03:07:24 AM
Quote from: wildwood on November 07, 2011, 10:31:07 PM
Ooh errr Missus................ A tube fender set for a YJ Mark??? And you a L***d R***r person???

What can i say?....I collect stuff/crap :003:

Yup they be the one JJ had :icon_winkle:

got any pics?
Logged
Pages: [1]   Go Up
« previous next »
 
Powered by EzPortal