Birty Dastards Jeep Club

Please login or register.

Login with username, password and session length
Advanced search  
Pages: [1]   Go Down

Author Topic: Lights  (Read 5972 times)

0 Members and 1 Guest are viewing this topic.

Anonymous

  • Guest
Lights
« on: May 15, 2006, 03:06:24 PM »
Anyone know if the KC windshield light brackets will accept easily other makes of lights .....Hella 500's Im guessing the bolt size for mounting are similar
Logged

Anonymous

  • Guest
(No subject)
« Reply #1 on: May 15, 2006, 03:34:25 PM »
Just put some 8" Cibies on mine, will post some pics later and measure the slot :)

EE :twisted:
Logged

chrisjones

  • Forum Member
  • *
  • Guru: 4
  • Offline Offline
  • Posts: 5841
  • Vehicle: Dogface
  • Sometimes I wonder....
(No subject)
« Reply #2 on: May 15, 2006, 03:38:12 PM »
Quote from: "EvilEd"
Just put some 8" Cibies on mine, will post some pics later and measure the slot :)

EE :wink:  :D
Logged
God was my copilot but we crashed in the mountains and I had to eat him.

Anonymous

  • Guest
(No subject)
« Reply #3 on: May 15, 2006, 04:28:10 PM »
Quote from: "chrisjones"
Quote from: "EvilEd"
Just put some 8" Cibies on mine, will post some pics later and measure the slot :)

EE :wink:  :twisted:
Logged

Anonymous

  • Guest
(No subject)
« Reply #4 on: May 15, 2006, 10:35:29 PM »
mmore says the holes 12mm diametre...Hella bolts are 8mm
That would make a plan come together and make my front winch bumper scheme much easier
Logged

Anonymous

  • Guest
(No subject)
« Reply #5 on: May 16, 2006, 09:15:51 AM »
I'd tent to agree with the ~12mm width... just enjoy wiring them up.... and find the two hidden screws where you have to remove the rubber at the back of the bonnet... :)
Logged

Anonymous

  • Guest
(No subject)
« Reply #6 on: May 18, 2006, 09:53:12 PM »
The project moves on....... 8)
Logged

Anonymous

  • Guest
(No subject)
« Reply #7 on: May 18, 2006, 11:09:04 PM »
Have you done it ???? Post pics :)
Logged

wrangler

  • Forum Member
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 2109
    • http://www.manxteaandcoffee.com
(No subject)
« Reply #8 on: May 19, 2006, 07:55:09 AM »
I changed a hole wind screen and surround from one 97 Tj to another and had no problems with the Torx bolts!
Logged

Anonymous

  • Guest
(No subject)
« Reply #9 on: May 19, 2006, 10:19:57 AM »
oops, I missed that bit... I bought a socket set of torx bits from 4wd... use the impact driver the loosen them and they came out dead easy.... Oh, and a nice big hammer..... :twisted:
Logged

Anonymous

  • Guest
(No subject)
« Reply #10 on: May 19, 2006, 05:22:48 PM »
KC light brackets on order from Outback Automotive

12.5% discount to all Birtys emailing enquirys through first :D
Logged

Anonymous

  • Guest
(No subject)
« Reply #11 on: May 29, 2006, 05:11:20 PM »
Job done....If only I had a camera
Logged

Anonymous

  • Guest
(No subject)
« Reply #12 on: May 29, 2006, 05:58:38 PM »
How did it go Stew....
Logged

Anonymous

  • Guest
(No subject)
« Reply #13 on: May 29, 2006, 06:11:13 PM »
Good

Fitting the brackets went much better than I expected
Got an auto electrician in to move them after I'd taken the cowl off as you advised :wink:
He was actually from the place that fitted the lights.. He wired them up past the battery for the relay near the N/S front head lamp and then drilled a hole in the front bulkhead (below the rubber strip)  and ran the wiring through there to the lights

Then I put the wiring behind the windscreen hinges to re-fit the cowl and moved the lights to the front of the brackets in order that the aeriel wasn't bent

Just got to align them now :D
Logged

ExtremeTJ

  • Guest
(No subject)
« Reply #14 on: May 29, 2006, 09:38:01 PM »
Logged
Pages: [1]   Go Up
« previous next »
 
Powered by EzPortal