Topic: TJ Disconnects (Read 7965 times)

Anonymous · « **on:** October 29, 2005, 10:27:53 PM »

Got the disco's with the centre tube with pins to hold it in place top and bottow (4WD?)

What do I need to do to stop the stabiliser bar swinging down once disconnected ?

greggmo · « **Reply #1 on:** October 29, 2005, 10:37:39 PM »

tie it to somethin... dumb ass. :lol:

trent · « **Reply #2 on:** October 29, 2005, 10:48:58 PM »

Stew, just use some cable ties and strap her up to whatever you can :wink:

Anonymous · « **Reply #3 on:** October 29, 2005, 11:03:38 PM »

Yep that was what I was thinking

Better clean the wheel arches out and find something :shock:

isle of man · « **Reply #4 on:** October 29, 2005, 11:51:57 PM »

some people weld something to the chassis and clip to it....others just use cable tie but it never lasts.......and they re-tie and re-tie and re-tie get the message.

peter henry

trent · « **Reply #5 on:** October 30, 2005, 12:04:44 AM »

Stew, a cable tie will hold for the time/day your offroad :shock:
Nowt wrong with welding a clip thats the best long term solution, but a cable tie cost only pennies and does the job perfectly

daggie · « **Reply #6 on:** October 30, 2005, 03:09:14 AM »

Stew
get yerself down to b&q & have a look at the brackets the have, I got two little u shaped brackets & simply driilled & screwed them to the chassis rail.
easy peesy :wink:

Mort · « **Reply #7 on:** October 30, 2005, 08:24:19 AM »

Stew

If you take a look at the front of the wheel arch, towards the top, you'll see that there's a a triangular metal sheet that's just behind the indicators, but on the inside, that's used to mount the wiring loom. This has a hole on the inside edge that's not used for anything so far as I can see.

You can either thread a zip tie through this hole and through your anti-roll bar, or you can do what I've done, which is to buy a stainless eye bolt and mount this through that hole, facing the wheel. Then just put a zip tie through the eye and through the hole at the end of your anti-roll bar.

Dead easy, and no drilling. You can get a suitable stainless eye bolt from a chandlers - there must be loads up your way due to the canal.

I can post piccies if you want them.

Anonymous · « **Reply #8 on:** October 30, 2005, 09:47:00 AM »

Got a stock of cable ties already
Thanks all for the input
Appreciated

Mort · « **Reply #9 on:** October 30, 2005, 10:14:16 AM »

Stew

Worth mentioning that it's best to move the anti-roll bar up as far as possible before securing with with a zip tie. That way you can be sure that your tyres won't touch it during articulation.

Anonymous · « **Reply #10 on:** October 30, 2005, 10:30:17 AM »

Thanks

Woody · « **Reply #11 on:** October 30, 2005, 12:24:41 PM »

Stew

or you can try the Woody Deluxe Swaybay holding device. Get down to your local camping shop and and buy a length of the nylon webbing and 2 of the quick release plastic buckle (the type you find on rucksacks). With a little bit of sewing you will have made up 2 straps, all you need to do then is pop rivet or bolt it onto the bulkhead Mort described above. Will cost under a fiver, is quick to do up and release, no more fumbling trying to do up cable ties or cut them afterwards :shock:

If you want I can take photos of it.

Woody

Anonymous · « **Reply #12 on:** October 30, 2005, 01:03:56 PM »

All food for thought Thanks all Im having another look this pm or tomorrow evening see what I reckon

Chhers again

Stew

Mort · « **Reply #13 on:** October 30, 2005, 05:17:09 PM »

Can you post a photo of you sewing Woody? :smt040 :smt079

Anonymous · « **Reply #14 on:** October 30, 2005, 07:21:17 PM »

:lol: :lol: :lol: :lol:

46stm · « **Reply #15 on:** October 30, 2005, 08:27:04 PM »

what made you buy that style of disconnect rather than JKS ones ?

Personally I've never liked cable ties, not positive enough although loads of people use them. Be careful and check that on full lock with wheel stuffed right up in the arch that your muds don't rip the cable ties apart as they touch the sway bar.

Anonymous · « **Reply #16 on:** October 30, 2005, 08:44:27 PM »

Hi It was all part of my plan, Points noted about ripping the cable ties off tho

Woody · « **Reply #17 on:** October 30, 2005, 09:25:36 PM »

Mort

don't worry with my solution you still get to enjoy latex gloves. You should see the look on a newby Winch Bitches face after parking in the middle of nowhere and then you pull out the gloves :shock:

Woody

46stm · « **Reply #18 on:** October 30, 2005, 09:50:23 PM »

yeah Woody you scared me last Sunday with the latex gloves in the woods, it'd be ok if you had a toolkit in your hand not just your tool ....lol

did video it though and watched it later !

Anonymous · « **Reply #19 on:** October 31, 2005, 08:43:09 AM »

You lot been watching Deliverance again?

Woody · « **Reply #20 on:** October 31, 2005, 06:57:15 PM »

Steve

you must have good eyesight :roll:

Woody

Bubba · « **Reply #21 on:** October 31, 2005, 09:57:52 PM »

cable ties just use big bastards no probs

cabletow · « **Reply #22 on:** November 04, 2005, 10:19:23 PM »

Get a Currie antirock or a sway loc and never get out of your seat

I have an antirock and a swayloc for sale if you are interested

Anonymous · « **Reply #23 on:** November 05, 2005, 05:13:25 PM »

Going to stick with what I've got for a few events and then consider my options

isle of man · « **Reply #24 on:** November 05, 2005, 06:09:23 PM »

i have had the currie front sway bar on one of my wranglers, it works ok once you set it for what you need......on my new wrangler my choice is the teraflex system......now that is some bit of kit...twist and loc, the best ever.

peter henry

Author Topic: TJ Disconnects (Read 7965 times)

Anonymous

Anonymous

Mort

Anonymous

Mort

Anonymous

Woody

Anonymous

Mort

Anonymous

46stm

Anonymous

Woody

46stm

Anonymous

Woody

cabletow

Anonymous