Birty Dastards Jeep Club

Please login or register.

Login with username, password and session length
Advanced search  
Pages: [1]   Go Down

Author Topic: Torque shaft kit?  (Read 2708 times)

0 Members and 1 Guest are viewing this topic.

pafc11

  • Guest
Torque shaft kit?
« on: June 01, 2009, 10:24:36 PM »
Looking for a kit which i have heard is available but cant place at mo. The Torque shaft bush. boot and bushing retainer, (technical name for ordering would be handy :roll:  )

locked into 2wd only at moment, when i select any other drive the shaft is so worn it pops out and leaves me stuck in nuetral.

anyone ever had this problem and what was your solution. many thanks.
Logged

Bubba

  • "Cooter"
  • Marshal
  • Guru
  • *
  • Guru: 69
  • Offline Offline
  • Posts: 21029
Re: Torque shaft kit?
« Reply #1 on: June 01, 2009, 10:28:33 PM »
dunno mate i broke my stink bone once if it helps any






wait for the xj guys to come along i am sure they will know
Logged


trucks


shedric
cletus
mr whippy

I spent most of my money on alcohol, women and old  iron........ the rest of it I just wasted.

Mike Pavelin

  • Guest
Re: Torque shaft kit?
« Reply #2 on: June 07, 2009, 10:25:30 PM »
I don't think anyone here knows what you're on about. Can you describe what it is you're calling a torque shaft?
Logged

pafc11

  • Guest
Re: Torque shaft kit?
« Reply #3 on: June 08, 2009, 06:04:34 PM »
ok if pic has loaded properly, its this part of the jeep im on about,

mine keeps popping out at the bracket and bushing bit. will try to get part end of month if i can, has an old leak has just reappeared :-(
Logged

PtP

  • Club Member
  • Guru
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 872
  • Stourbridge, West Midlands
Re: Torque shaft kit?
« Reply #4 on: June 08, 2009, 11:03:27 PM »
The one on my TJ rattles quit a lot, but works fine.

I too would be interested in knowing if there is a replacement “Bronze Bushing Retainer” as it seems to be that end which rattles.

Have a look at this mod posted on here a while back:

Quote from: "Steve B"
Today I fitted the transfer case linkage relocator.

It set up quite easily and is now completely mounted to the gearbox and has a real positive feel rather than the vague is it or isn't it in feel.

I also cut a space to allow for the front driveshaft droop as it was rather close.

Upon refitting the skid today one on the stainless 1/2  13 tpi  bolts stripped itself!!!!  cheap bolt from ebay. I had a sort through my spares and found the old torx bolts from my front bumper which were perfect. I only have 4 though and need 6.  If anyone has 2 of these which they no longer use I would be grateful if I could buy them.  thanks.  Steve











Logged
Peter

The Smiths

  • Forum Member
  • *
  • Guru: 1
  • Offline Offline
  • Posts: 1084
Re: Torque shaft kit?
« Reply #5 on: June 09, 2009, 10:28:45 AM »
I managed to screw mine up - when crossmember went and front prop chewed it all out. :-D )

Then it is just a case of crawling under it and pushing them back in - and bending the bracket back :lol: .
Logged
If you always do what you have always done You will always get what you have always got
Please give to our Mac4x4 fund: http://www.justgiving.com/The-Smiths-2015

Mike Pavelin

  • Guest
Re: Torque shaft kit?
« Reply #6 on: June 09, 2009, 05:20:09 PM »
Check your engine and gearbox mountings are ok.
Logged
Pages: [1]   Go Up
« previous next »
 
Powered by EzPortal