Birty Dastards Jeep Club

Please login or register.

Login with username, password and session length
Advanced search  
Pages: [1]   Go Down

Author Topic: XJ Shock mount  (Read 11239 times)

0 Members and 1 Guest are viewing this topic.

Anonymous

  • Guest
XJ Shock mount
« on: October 06, 2005, 08:02:36 PM »
On they way back form work tonight there wa a knocking doung form the drivers rear side. Had a look and the shocker is lose! Where ir fastens onto the body of the car at the top end, well its broken off!
THe shock is fine but it looks like the mount for it has broken off from the body!
It looks like the sort of job that may take more than my 'No More Nails'

DO I have to get a new mounting? How does it fit on?
Logged

chrisjones

  • Guru
  • *
  • Guru: 4
  • Offline Offline
  • Posts: 5841
  • Vehicle: Dogface
  • Sometimes I wonder....
(No subject)
« Reply #1 on: October 06, 2005, 08:10:36 PM »
The top shock mount has a pin though it.  The ends of the pin are flattened and have holes in them.  There are two smallish bolts that bolt into captive nuts in the body.  Either the bolts have come loose (not likely as they're usually seased(SP)) or they've bust, or the shock bush is compleatly fubared.

If all else fails, you can get ya fingers into the frame to put a nut and bolt on. :wink:

You'll need to take a closer look to be sure what's happened
Logged
God was my copilot but we crashed in the mountains and I had to eat him.

greggmo

  • Founder
  • Guru
  • *
  • Guru: 2
  • Offline Offline
  • Posts: 8230
(No subject)
« Reply #2 on: October 06, 2005, 08:11:07 PM »
you can knock the captive nuts out and put a nut and bolt through. or you could drill and tap em mate.
Logged

Anonymous

  • Guest
(No subject)
« Reply #3 on: October 06, 2005, 08:18:07 PM »
Dont know about not buying lucky heather mate, have you pissed on a gypsie or what, your lucks gotta change soon  :wink:
Logged

Anonymous

  • Guest
(No subject)
« Reply #4 on: October 06, 2005, 08:32:00 PM »
So is this gonna be an expensive thing to sort out?
Logged

Mick O

  • Mickosaurus
  • Founder
  • Guru
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 2426
(No subject)
« Reply #5 on: October 06, 2005, 08:33:03 PM »
Owen mate

Have a look at this

http://http://jeephorizons.com/tech/xjshock.html

Dont panic, this is not uncommon on XJs

 8)  :smt025
Logged
I'm not a complete idiot.......................some bits are missing


AKA Jurassic O




monkeybiz

  • Guest
(No subject)
« Reply #6 on: October 06, 2005, 08:36:34 PM »
we have seen it a couple of times, the drivers side upper shock nut just comes loose for some unkown reason. if you have lost the bits give us a ring im sure we have spares we could send you foc
Logged

chrisjones

  • Guru
  • *
  • Guru: 4
  • Offline Offline
  • Posts: 5841
  • Vehicle: Dogface
  • Sometimes I wonder....
(No subject)
« Reply #7 on: October 06, 2005, 08:38:07 PM »
Cor!  That's not in this country!!  It's not covered in shit! :lol:
Logged
God was my copilot but we crashed in the mountains and I had to eat him.

Anonymous

  • Guest
(No subject)
« Reply #8 on: October 06, 2005, 08:48:27 PM »
Quote from: "greggmo"
you can knock the captive nuts out and put a nut and bolt through. or you could drill and tap em mate.


There is shag all room above to get the bolt in.

Best way is to get some U section steel welded to the underside to replace the bar pins, I did that on one of mine, also managed to drill and tap another one, crap job to do without a lift
Logged

chrisjones

  • Guru
  • *
  • Guru: 4
  • Offline Offline
  • Posts: 5841
  • Vehicle: Dogface
  • Sometimes I wonder....
(No subject)
« Reply #9 on: October 06, 2005, 09:52:40 PM »
You CAN stick a nut on the back.  I know cos we did it on mine. :wink:
Logged
God was my copilot but we crashed in the mountains and I had to eat him.

Anonymous

  • Guest
(No subject)
« Reply #10 on: October 07, 2005, 08:00:29 AM »
bloody hell you must have small hands, I couldnt get my fingers between the 2 pieces of metal
Logged

chrisjones

  • Guru
  • *
  • Guru: 4
  • Offline Offline
  • Posts: 5841
  • Vehicle: Dogface
  • Sometimes I wonder....
(No subject)
« Reply #11 on: October 07, 2005, 08:03:53 AM »
T'wasn't me, t'was Bubba.

OR....you've just got fat fingers! :lol:
Logged
God was my copilot but we crashed in the mountains and I had to eat him.

Anonymous

  • Guest
(No subject)
« Reply #12 on: October 07, 2005, 05:12:00 PM »
Your not gonna believe this!
Just come in form the garage when the put it up on the ramp, asked me to come and take a look at it!
THE SHOCKS MOUNTINGS TURNED OUT TO BE SELF TAPPING SCREWS :shock:

No bolts keeping them attached, just self tappers! And then the garage said they would have to cut the whole section out each side and weld a new section in. I cant help thing thats just bollocks!
Logged

greggmo

  • Founder
  • Guru
  • *
  • Guru: 2
  • Offline Offline
  • Posts: 8230
(No subject)
« Reply #13 on: October 07, 2005, 05:36:57 PM »
it might have self tapprs in it as the result of someones bad workmanship i fitting the lift. dont let the garage fleese you mate. get under and knock out the captives and put a nut in their place. or drill and tap em itaint that bad to do. we did it on jonah,s lift when one of the bolts broke.
Logged

JamesH

  • Club Member
  • Guru
  • *
  • Guru: 1
  • Offline Offline
  • Posts: 4998
  • Vehicle: JK
  • Year: 2010
(No subject)
« Reply #14 on: October 07, 2005, 05:37:42 PM »
It's not that big a deal.

If the original holes are there, drill and re-tap with an appropriate size (8mm should do it). Then reattach with original bar pins if okay, or replace bar pins and reattach.

I think I may have at least one Old Man Emu bar-pin (somewhere in shed?!) that could be used if you need it.

Don't let a garage start cutting bits out and welding new sections in, I can't believe it's that bad - you don't damage vehicles intentionally do you?  :wink:
Logged

chrisjones

  • Guru
  • *
  • Guru: 4
  • Offline Offline
  • Posts: 5841
  • Vehicle: Dogface
  • Sometimes I wonder....
(No subject)
« Reply #15 on: October 07, 2005, 05:45:29 PM »
Big hammer, small punch and a couple of new nuts and bolts. :wink:

Like Greggmo said, we did it on mine.  It's not difficult, just fiddly.
Logged
God was my copilot but we crashed in the mountains and I had to eat him.

daggie

  • Moderator
  • Guru
  • *
  • Guru: 3
  • Offline Offline
  • Posts: 3447
(No subject)
« Reply #16 on: October 07, 2005, 05:59:37 PM »
we're gonna repair it next saturday  :wink:
& give it a good going over

Did I mention, Owen makes a good cuppa  :D
Logged
Grand cherry, 3.0 crd Overland
Grand cherry, 2.7 crd
95, Cherry, aka Blackie      P38 range rover

monkeybiz

  • Guest
(No subject)
« Reply #17 on: October 07, 2005, 07:05:30 PM »
owen change your garage now............. they are fleecing you, if you werent so far away i would come round and do it for you, its not difficult, just fiddly for those of us with fat sausage fingers, luckily mine are long sausage fingers and not the stubby veriety you get on the average garage morlock


gwyn














so who's making this cuppa then??? is there pizza to go with it
Logged

Bubba

  • "Cooter"
  • Marshal
  • Guru
  • *
  • Guru: 69
  • Offline Offline
  • Posts: 21029
(No subject)
« Reply #18 on: October 07, 2005, 08:56:30 PM »
dont fret owen tis easy to fix
Logged


trucks


shedric
cletus
mr whippy

I spent most of my money on alcohol, women and old  iron........ the rest of it I just wasted.

Anonymous

  • Guest
(No subject)
« Reply #19 on: October 08, 2005, 06:51:16 AM »
Cheers Kev, was just looking foward to streaching her legs on Sunday with you guys! :cry:
Logged
Pages: [1]   Go Up
« previous next »
 
Powered by EzPortal