Birty Dastards Jeep Club

Please login or register.

Login with username, password and session length
Advanced search  
Pages: [1]   Go Down

Author Topic: Any one ever used Protectakote  (Read 4960 times)

0 Members and 1 Guest are viewing this topic.

Bigfeetrob

  • Guest
Any one ever used Protectakote
« on: April 16, 2013, 10:33:33 PM »

I'm tarting up the interior of the cj7

I have pulled out all the old manky carpet and was wondering if it was a good idea
to lay a coat or 2 of this protectaKote down either underneath or instead of new carpet

http://www.anti-slip-paint.co.uk/protectakote-bedvan-liner-black-p-4.html

Any one had experience of it good or bad. Does it last and is it as good as it sounds ?

Rob
Logged

Jonny Jeep

  • Regular Member
  • Forum Member
  • *
  • Guru: 11
  • Offline Offline
  • Posts: 1372
  • Vehicle: TJ 4.0 Sport
  • Year: 1997
Re: Any one ever used Protectakote
« Reply #1 on: April 16, 2013, 10:47:42 PM »

I've used it, but only recently at work to line the floor on the inside of a Ford Fiesta I think. All the carpets had completely worn through so it needed something as the grip paint that had been used previously had worn through too. That was just cheaper stuff that's like paint with sand in it.

I don't know if the vehicle is still at Manchester or it's been sent to another airport. I'll look for it if I get a chance tomorrow and if it's still at MAN I'll get a pic or two of the finish. It goes on easy enough but does need decent ventilation when going on and can't be got wet till dried. Gets tacky in about four hours for recoating and full cure takes 2-3 days. As with most things good preparation is the key. You get rollers and paint brushes with the 4L kit. I just stippled it on with a brush as only doing the floor.
Logged

Bulldog67

  • Arthur Daley: Graduated
  • Guru
  • *
  • Guru: -936
  • Offline Offline
  • Posts: 25395
  • Vehicle: Man Sized Old Iron
  • Anti Colour Truck Mafia - I'm The Fuckin Daddy
Re: Any one ever used Protectakote
« Reply #2 on: April 16, 2013, 10:48:37 PM »

Its shit, like rollerin on little spikes of glass, anything touches it is shredded

Swimmin pool rubber paint in mine , dogs bollox, & oil resistant blah blah

I did put protectacote on my bonnet by mistake tho (was v sunny & I picked up the wrong can  :003: ) & it has lasted ok
Logged
Bulldog's 22+ trucks: http://www.birtydastards.com/frm/index.php?topic=20288.0 :025:                                   :headbanger: 401 Dog * 401 Molotov :headbanger:  
Civilise the mind but make savage the body  :027:           Im only responsible for my karma :059:

Jonny Jeep

  • Regular Member
  • Forum Member
  • *
  • Guru: 11
  • Offline Offline
  • Posts: 1372
  • Vehicle: TJ 4.0 Sport
  • Year: 1997
Re: Any one ever used Protectakote
« Reply #3 on: April 16, 2013, 10:52:03 PM »

Maybe it's because I only used a brush but it's fairly smooth in the car I did. As I said I'll see if it's about for pics.
Logged

Bigfeetrob

  • Guest
Re: Any one ever used Protectakote
« Reply #4 on: April 16, 2013, 11:14:00 PM »

Cheers Jonny - always good to get someone that has used it. Be interested to hear how it's holding up and pics would be great

Bd - nice one, had not even thought about pool paint. Have you got carpet on top of it or is it good enough to have as a floor covering.
Ideally I'm after a tough finish that can be swept out when looking rough, even a quick wash over with a wet sponge and shazam good as new

Cheers
Logged

Nosebolt

  • Guest
Re: Any one ever used Protectakote
« Reply #5 on: April 17, 2013, 12:17:23 AM »

all of tonk a is done inside and don't listen to BD, best thing I ever did for the CJ


Logged

Bulldog67

  • Arthur Daley: Graduated
  • Guru
  • *
  • Guru: -936
  • Offline Offline
  • Posts: 25395
  • Vehicle: Man Sized Old Iron
  • Anti Colour Truck Mafia - I'm The Fuckin Daddy
Re: Any one ever used Protectakote
« Reply #6 on: April 17, 2013, 07:40:34 AM »

Try a wash n dry on it!

No carpets, & yes will just wash n dry and off you go. Comes in liads of colours as well
Logged
Bulldog's 22+ trucks: http://www.birtydastards.com/frm/index.php?topic=20288.0 :025:                                   :headbanger: 401 Dog * 401 Molotov :headbanger:  
Civilise the mind but make savage the body  :027:           Im only responsible for my karma :059:

IrishCJ6

  • Guru
  • *
  • Guru: 3
  • Offline Offline
  • Posts: 1033
Re: Any one ever used Protectakote
« Reply #7 on: April 17, 2013, 08:31:52 AM »

I have a kit ready for the 6, I brought it before I painted her but my Dad did his and whilst its great and strong its a bugger to clean and will always look dirty due to the way dirt will get trapped in the undulations, I went with a heavy duty 2 pack industrial machine paint in matt black for mine. It's bloody strong stuff but does allow you to wipe down the inside properly.
Logged

cuffm

  • Guru
  • *
  • Guru: 0
  • Offline Offline
  • Posts: 207
  • Vehicle: XJ
  • Year: 1998
Re: Any one ever used Protectakote
« Reply #8 on: April 17, 2013, 09:00:30 AM »

The inside of my TJ tub was sprayed with protectakote over 10 years ago, lasted very well. Stood up to loads of abuse. Not to fussed about keeping it that clean, just brushed out Jeep every year or so! Can be a right pain to remove if you want to do any welding though. And they might have changed the mix since I last used it. 
Logged

Dave69

  • Club Member
  • Forum Member
  • *
  • Guru: 15
  • Offline Offline
  • Posts: 9457
  • Vehicle: CJ-7 4.2 auto
  • Year: 1979
Re: Any one ever used Protectakote
« Reply #9 on: April 17, 2013, 07:31:38 PM »

use a paint brush = smooth finish

use a roller = stippled finish.
Logged
XJ 2.5 diesel - dead. XJ 4.0 6" lift - sold to some lucky person
CJ7 4.2 auto standard(ish)
Alfa 147 jtdm

Bulldog67

  • Arthur Daley: Graduated
  • Guru
  • *
  • Guru: -936
  • Offline Offline
  • Posts: 25395
  • Vehicle: Man Sized Old Iron
  • Anti Colour Truck Mafia - I'm The Fuckin Daddy
Re: Any one ever used Protectakote
« Reply #10 on: April 17, 2013, 08:03:01 PM »

U may wanna read above dave
Logged
Bulldog's 22+ trucks: http://www.birtydastards.com/frm/index.php?topic=20288.0 :025:                                   :headbanger: 401 Dog * 401 Molotov :headbanger:  
Civilise the mind but make savage the body  :027:           Im only responsible for my karma :059:

Jonny Jeep

  • Regular Member
  • Forum Member
  • *
  • Guru: 11
  • Offline Offline
  • Posts: 1372
  • Vehicle: TJ 4.0 Sport
  • Year: 1997
Re: Any one ever used Protectakote
« Reply #11 on: April 18, 2013, 06:58:35 PM »

Got a pic. The car hasn't been anywhere it's outside the workshop stuffed into a corner. Put the key there for scale so you can get a better idea of the finish, which as I said was stippled with a brush.

Logged

nomadsz

  • Guest
Re: Any one ever used Protectakote
« Reply #12 on: April 18, 2013, 08:32:28 PM »

spraying tends to give the best results i have used it inside and out and i am not that impressed when applying by brush and roller.

you might want to try a professional spray job by line-x seen some of there work and i have been very impressed.
Logged

chrisjones

  • Forum Member
  • *
  • Guru: 4
  • Offline Offline
  • Posts: 5841
  • Vehicle: Dogface
  • Sometimes I wonder....
Re: Any one ever used Protectakote
« Reply #13 on: April 18, 2013, 08:41:59 PM »

Got to say I'm tempted to do the inside of DF with it.
Logged
God was my copilot but we crashed in the mountains and I had to eat him.

Bigfeetrob

  • Guest
Re: Any one ever used Protectakote
« Reply #14 on: April 19, 2013, 07:24:53 PM »

Will it go through a spray gun though  :017: I thought it had bits of rubber mixed into it to give it the anti slip finish which would clog a spray gun ( my knowledge of spraying starts and ends with the word spraying )

Thanks for the pic Jonny, it looks quite lumpy in that pic...

The finish looks really good in nosebolts tub was that sprayed on or roller ?

I think I will give it a try and see how it goes, will report back with results
Logged

Nosebolt

  • Guest
Re: Any one ever used Protectakote
« Reply #15 on: April 19, 2013, 07:32:25 PM »

use a roller, has to be a foam type not a furry one, I got my best result by doing a quick thin coat and letting it tack off then over with a heavy coat, wait five mins then over again with the roller but no extra paint, rolling in one direction only.
Logged

jebbench

  • Guest
Re: Any one ever used Protectakote
« Reply #16 on: April 19, 2013, 08:53:52 PM »

Let us know how you get on if you do go down the Protectakote route. I've been looking for something like it and even considering the Line-X route (they'd do a much neater job than I could even dream of), big price difference though.
Logged

Bulldog67

  • Arthur Daley: Graduated
  • Guru
  • *
  • Guru: -936
  • Offline Offline
  • Posts: 25395
  • Vehicle: Man Sized Old Iron
  • Anti Colour Truck Mafia - I'm The Fuckin Daddy
Re: Any one ever used Protectakote
« Reply #17 on: April 19, 2013, 08:55:44 PM »


I think I will give it a try and see how it goes, will report back with results

when its shite

I will  resist the lure of sayin I told you so  :greggmo:

I especially wont mention that just coz there is a clever advertisin campaign to reel in the suckers into usin a really annoyin product .............

rather than breakin from the flock
Logged
Bulldog's 22+ trucks: http://www.birtydastards.com/frm/index.php?topic=20288.0 :025:                                   :headbanger: 401 Dog * 401 Molotov :headbanger:  
Civilise the mind but make savage the body  :027:           Im only responsible for my karma :059:
Pages: [1]   Go Up
 

Powered by EzPortal