May 15, 2025, 02:21:36 PM
Welcome,
Guest
Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Home
Forum
Help
Login
Register
GALLERY
Unread
Events
Birty Dastards Jeep Club
>
Forum
>
Tech Forum
>
Workshop
>
Topic:
Xj mk2 immobiliser issues
« previous
next »
Pages: [
1
]
Go Down
Print
Author
Topic: Xj mk2 immobiliser issues (Read 4328 times)
0 Members and 1 Guest are viewing this topic.
Toptooler
Guru
Guru: 0
Offline
Posts: 174
Vehicle: Wrangler JK
Year: 2009
Xj mk2 immobiliser issues
«
on:
November 14, 2014, 06:41:07 PM »
Ok here the issue battery disconnected for 10 days due to engine rebuild my own fault water too deep snorkel pipe was adrift from bottom of air box.
This is Carloses old xj mk2 auto 4.0l purple.
Garage rings me today and says the car will crank over but not start no power to ignition coil.
The only problem is the immobiliser never worked before or the fob for the central door locking it's has a grey key.Key has been in the ignition the whole time the battery has been disconnected.
All the lights come on as normal then go out as normal when you turn ignition and turns over ,the red light in the front of centre consul stays on never seen this on before presume this is the immobiliser light but now on all the time.
So whats the problem and how to solve it ?
Cheers Mark
Logged
Mike Pavelin
Guest
Re: Xj mk2 immobiliser issues
«
Reply #1 on:
November 14, 2014, 07:31:02 PM »
If it has a grey SKIS key it is unlikely to be an immobiliser fault unless there is a key symbol flashing on the das. Scan it for fault codes.
Logged
JamesH
Club Member
Guru
Guru: 1
Offline
Posts: 4998
Vehicle: JK
Year: 2010
Re: Xj mk2 immobiliser issues
«
Reply #2 on:
November 14, 2014, 09:19:42 PM »
Immobiliser probs normally show by engine starting and then dying after 3 secs. If you scan you might find the crank or cam sensor at fault or a short to ground somewhere - even if it was fine before.
Logged
Brynjaminjones
"Abe Lincoln"
Club Member
Guru
Guru: 8
Offline
Posts: 2444
Vehicle: '98 XJ Cherokee 4.0 Limited, '97 ZJ Grand Cherokee 4.0 Limited, '91 Hunter Green SJ Grand Wagoneer 360
Re: Xj mk2 immobiliser issues
«
Reply #3 on:
November 14, 2014, 09:24:38 PM »
It probably won't be much help, and Mike probably knows exactly what it says already, but I've got the original alarm/immobiliser handbook from my '98 XJ if you want me to scan it in for you?
Logged
Toptooler
Guru
Guru: 0
Offline
Posts: 174
Vehicle: Wrangler JK
Year: 2009
Re: Xj mk2 immobiliser issues
«
Reply #4 on:
November 14, 2014, 09:41:02 PM »
Evening
Thanks for your responses, key symbol goes out on dash when ignition is turned on after a few seconds.
I think garage said no error codes will check in morning.
Thanks again Mark
Logged
bagofsand
Guest
Re: Xj mk2 immobiliser issues
«
Reply #5 on:
November 15, 2014, 07:02:42 AM »
not sure if your xj has the same system as my 99 TJ may and schofield with grey key, however your fault sounds the same. solid immobiliser light on turning over but no spark. My fix was to get a USA pcm that didn't have the immobiliser activated, I did read that on some jeeps the immo was just piggy backed onto the pcm and could simply be unplugged from the loom. also you might be able to use a pcm from an earlier model.
Logged
big g
Guest
Re: Xj mk2 immobiliser issues
«
Reply #6 on:
November 15, 2014, 07:44:28 AM »
Think skis is factory fit,different set up to May Schofield system.
Logged
Mike Pavelin
Guest
Re: Xj mk2 immobiliser issues
«
Reply #7 on:
November 15, 2014, 08:39:25 AM »
SKIS TJs (98 on) had a similar looking May and Schofield unit retro fitted but it did not immobilise the vehicle.. It was solely there to allow a dealer fit May and Schofield alarm system upgrade to be fitted.
Logged
Toptooler
Guru
Guru: 0
Offline
Posts: 174
Vehicle: Wrangler JK
Year: 2009
Re: Xj mk2 immobiliser issues
«
Reply #8 on:
November 15, 2014, 09:16:47 AM »
Morning
Been to garage guy is not in who's working on jeep
Have been offered a us spec PCM to try from Yakko
Will take to garage on Monday
Logged
Yakko
Guest
Xj mk2 immobiliser issues
«
Reply #9 on:
November 15, 2014, 10:51:02 AM »
My US PCM is from a manual non SKIS TJ, will that work in an auto SKIS XJ?
Logged
Toptooler
Guru
Guru: 0
Offline
Posts: 174
Vehicle: Wrangler JK
Year: 2009
Re: Xj mk2 immobiliser issues
«
Reply #10 on:
November 21, 2014, 05:11:39 PM »
Goodnews jeep now running needed new crank sensor but no error codes for that came up.
Thanks again birtys to the rescue
Logged
Brynjaminjones
"Abe Lincoln"
Club Member
Guru
Guru: 8
Offline
Posts: 2444
Vehicle: '98 XJ Cherokee 4.0 Limited, '97 ZJ Grand Cherokee 4.0 Limited, '91 Hunter Green SJ Grand Wagoneer 360
Re: Xj mk2 immobiliser issues
«
Reply #11 on:
November 21, 2014, 05:18:54 PM »
Good result
Logged
Print
Pages: [
1
]
Go Up
« previous
next »
Birty Dastards Jeep Club
>
Forum
>
Tech Forum
>
Workshop
>
Topic:
Xj mk2 immobiliser issues
Powered by
EzPortal
Go Up
Go Down