Topic: Bonnet Release (Read 8071 times)

SB · « **on:** November 05, 2006, 05:35:50 PM »

Hi your help and advice required.

Am now on my third bonnet release cable on my N reg Cherokee and it's becoming a bit of a pain replacing them.
My plan is to fit lockable bonnet release pins instead and do away with the release cable completely. Therefore my question to you guys is would the vehicle pass the MOT with these fitted and no release cable? As I interpret the DOT MOT advice pages it does mention that you must be able to release the bonnet quickly but doesn't mention where from!
Thanks in advance for your help
Steve

MK1 · « **Reply #1 on:** November 05, 2006, 05:44:29 PM »

I can't think of any reason why it would fail as long as it fastens securely.

Manda · « **Reply #2 on:** November 05, 2006, 05:45:44 PM »

I have some lockable hood catches on my TJ the same as but in black:

I have got an MOT cert whilst they were on. I've still got the hood release too.

SB · « **Reply #3 on:** November 05, 2006, 05:49:44 PM »

Thanks for the swift replies have had various opinions on this from elsewhere but my take on it is if a rally car can pass an MOT on pins then it should be ok.
Manda, where did you source your pins from? Have seen some on ebay but they don't look as secure as yours

Thanks

Manda · « **Reply #4 on:** November 05, 2006, 05:55:33 PM »

They were from www.quadratec.com but I've had a quick look and they don't appear to do XJ ones. :?

I'm sure someone may be able to help more on that.

Bubba · « **Reply #5 on:** November 05, 2006, 08:50:11 PM »

i cant uderstand how you can have so much trouble with a bonnet cable but yup the rally jobs will work may even get them from halfrauds rippspeed bit

SB · « **Reply #6 on:** November 05, 2006, 11:19:13 PM »

Quote from: "V8 Bubba"

i cant uderstand how you can have so much trouble with a bonnet cable

The original cable had deteriorated and snapped so it was replaced 1 month ago. The replacement cable I put in was not new but seemed in good nick and that went on Saturday it broke in exactly the same place as the previous one.The weakest point on the cable appears to be at the cockpit end where the cable joins the handle as it has snapped here on each occasion.
Bonnet pins now appear to be the cheapest and most convenient option

greggmo · « **Reply #7 on:** November 05, 2006, 11:22:13 PM »

post up in the intro section sb. let us know who you are and what you are about.

Dave69 · « **Reply #8 on:** November 06, 2006, 08:00:44 AM »

give demon tweeks a ring for bonnect pins.

given the minimalistic approach to rally cars and mot's, fitting these to a normal car bonnet will be ok. If it is done well and no sharp edges you will have no problems

daggie · « **Reply #9 on:** November 06, 2006, 06:37:44 PM »

try putting a new one on it :? :roll:

SB · « **Reply #10 on:** November 06, 2006, 08:17:54 PM »

Have just sourced another cable to fit and have spoken to my motorsport contacts one of whom is supplying me some super duper pins as a back up!

Author Topic: Bonnet Release (Read 8071 times)

SB

Bonnet Release

MK1

(No subject)

Manda

(No subject)

SB

(No subject)

Manda

(No subject)

Bubba

(No subject)

SB

(No subject)

greggmo

(No subject)

Dave69

(No subject)

daggie

(No subject)

SB

(No subject)