Birty Dastards Jeep Club

Please login or register.

Login with username, password and session length
Advanced search  
Pages: [1]   Go Down

Author Topic: Alloy wheel question  (Read 5186 times)

0 Members and 1 Guest are viewing this topic.

keeko

  • Guest
Alloy wheel question
« on: December 13, 2006, 02:34:50 PM »
I`m due tires soon on my 1998 XJ and have just been offered a set of 16 inch wheels and tires (in excellent condtion) that came off a nearly new Freelander. The PCD is the same 5x114.3 but the offset is slightly different.
Would I be right in saying the offset is 20mm for the XJ? The freelanders is 35mm.
 I know they`re worth the money (£100!) but will the offset be a problem?
  cheers :?:
Logged

tim_aka_tim

  • Club Member
  • Forum Member
  • *
  • Guru: 1
  • Offline Offline
  • Posts: 4464
  • Vehicle: Honda Pilot
  • Year: 2008
  • Regional Organiser North America
(No subject)
« Reply #1 on: December 13, 2006, 03:40:09 PM »
PCD is the same, and from what I can see, so is the 35mm offset. However, the centre bore maybe a problem. On the Cherokee it's 71.5mm, but dunno what it is on the freeloader - possibly it's smaller. Also need to know if the studs will fit through the holes, and are they long enough for sufficient threads on the nut. And will the wheel rub on the caliper?
Logged

daggie

  • Moderator
  • Forum Member
  • *
  • Guru: 3
  • Offline Offline
  • Posts: 3447
(No subject)
« Reply #2 on: December 13, 2006, 03:44:56 PM »
try one first :idea:  :roll:
Logged
Grand cherry, 3.0 crd Overland
Grand cherry, 2.7 crd
95, Cherry, aka Blackie      P38 range rover

Mike Pavelin

  • Guest
(No subject)
« Reply #3 on: December 13, 2006, 05:31:13 PM »
Offset isn't an issue.it's the backspacing that can cause problems. Freelanders are frontwheel drive based so may well have too much backspacing causing the inner tyre walls to rub on the chassis and suspension when turning.
Logged

JamesH

  • Club Member
  • Forum Member
  • *
  • Guru: 1
  • Offline Offline
  • Posts: 4998
  • Vehicle: JK
  • Year: 2010
(No subject)
« Reply #4 on: December 13, 2006, 06:07:46 PM »
From what I can remember without looking it up:

Offset is the distance out from the centreline of the rim that the mounting face is located.

So for a 7" wide rim, an offset of zero would place the mounting face in the centre - giving a backspace measure of 3.5"

Working on that principle, for XJ rims 7" wide and 5.25" backspacing, I make offset as being 1.75" = 45mm.

I'm not 100% on this but think it's correct, there is information out there on this, try looking at some of the wheel manufacturer's websites and calculating from their backspace/offset measurements.
Logged

keeko

  • Guest
(No subject)
« Reply #5 on: December 13, 2006, 06:28:34 PM »
Some helpful replies there guys. Some erm........whoosh!. I` gonna try them on and go a run to see what the story is. If they seem  ok they`re getting bought. Even if i have to sell them on and turn a quid or two on them. :twisted:
Logged

Dodster

  • Guest
(No subject)
« Reply #6 on: December 13, 2006, 06:38:31 PM »
Logged

JamesH

  • Club Member
  • Forum Member
  • *
  • Guru: 1
  • Offline Offline
  • Posts: 4998
  • Vehicle: JK
  • Year: 2010
(No subject)
« Reply #7 on: December 13, 2006, 07:18:51 PM »
That's a good page Dodster, much clearer than my ramblings!
Logged

keeko

  • Guest
(No subject)
« Reply #8 on: December 20, 2006, 05:17:38 PM »
They were on. They`re now off/ I hate em :lol:   Proper jeep wheels or no wheels me thinks.
Logged

greggmo

  • Founder
  • Forum Member
  • *
  • Guru: 2
  • Offline Offline
  • Posts: 8230
(No subject)
« Reply #9 on: December 20, 2006, 05:36:14 PM »
ya knew all along it was wrong to put lardie bits on yer jeep anyway mate. 8)
Logged
Pages: [1]   Go Up
« previous next »
 
Powered by EzPortal