Birty Dastards Jeep Club

Please login or register.

Login with username, password and session length
Advanced search  
Pages: [1]   Go Down

Author Topic: Bit of advice and a bit of help needed  (Read 14866 times)

0 Members and 1 Guest are viewing this topic.

Anonymous

  • Guest
Bit of advice and a bit of help needed
« on: July 21, 2005, 09:27:37 AM »
Sadly its MOT time today and whilst checking out Mr TJ yesterday I discovered a blown drivers side reversing lamp bulb

Went to change it and upon removing the lens found the assembly full of water..might be worth checking out

However having checked the nearside one cause appears to be a missing foam rubber gasket thing
Any views where I can get a replacement 4 wd/Quadratec don't show one

dealer or lighthouse or is there a Halfords fix?
Logged

chrisjones

  • Guru
  • *
  • Guru: 4
  • Offline Offline
  • Posts: 5841
  • Vehicle: Dogface
  • Sometimes I wonder....
(No subject)
« Reply #1 on: July 21, 2005, 09:31:47 AM »
Try using some foam draft (?) excluder (??) from B&Q type place. :lol:
Logged
God was my copilot but we crashed in the mountains and I had to eat him.

Anonymous

  • Guest
(No subject)
« Reply #2 on: July 21, 2005, 09:44:48 AM »
Chris Thanks mate

Had thought of that just hoping there's a more automotive type option
Logged

Mort

  • Guest
(No subject)
« Reply #3 on: July 21, 2005, 10:13:34 AM »
I'd be inclined to go to a Dealer Stew.  It'll only cost a few quid, they'll be able to identify the right bit, and you'll save yourself a lot of hassle.
Logged

Anonymous

  • Guest
(No subject)
« Reply #4 on: July 21, 2005, 10:15:50 AM »
Stuff Pork Pies in the gap.... :)

Then use No Nails to make sure it's as tight as can be....

You could measure up for an O'Ring the right size if it's got a reasonable groove....

The Thin Bungee Strap they do in B&Q migt just do it as well....

Damn.... that was two sensible answers in one post...
Logged

Anonymous

  • Guest
(No subject)
« Reply #5 on: July 21, 2005, 10:24:33 AM »
That's what I was thinking...... not like you Ed!!! maybe you're just tired! :smt015
Logged

Anonymous

  • Guest
(No subject)
« Reply #6 on: July 21, 2005, 10:31:17 AM »
Momentary Lapse.... Won't happen again....

Mornin miss.... Don't you go reading none of those dirty posts from last night....
Logged

Anonymous

  • Guest
(No subject)
« Reply #7 on: July 21, 2005, 10:49:10 AM »
I was reading them when you were posting last night!!!!!   :cry:

Mornin' Ed  :blinkwave:
Logged

Anonymous

  • Guest
(No subject)
« Reply #8 on: July 21, 2005, 10:50:21 AM »
Neither Lighthouse nor Westbury have a suitable bit so I think its the B&Q route unless someone has a better idea
Logged

Anonymous

  • Guest
(No subject)
« Reply #9 on: July 21, 2005, 11:08:05 AM »
Go to B&Q, buy a roll of foam stick-on draft excluder stuff.............shame you aint in hereford, cos I got a load of it here cos we use it for sealing hobs to worktops........
Logged

Anonymous

  • Guest
(No subject)
« Reply #10 on: July 21, 2005, 11:54:18 AM »
Quote from: "She Devil"
I was reading them when you were posting last night!!!!!   :cry:

Mornin' Ed  :blinkwave:


Did you have to explain the important bits to him :)
Logged

Anonymous

  • Guest
(No subject)
« Reply #11 on: July 21, 2005, 01:08:49 PM »
Nah, he's a clever boy.......he knows all about the important bits!!!  :wink:
Logged
Pages: [1]   Go Up
« previous next »
 
Powered by EzPortal