Birty Dastards Jeep Club

Please login or register.

Login with username, password and session length
Advanced search  
Pages: [1]   Go Down

Author Topic: 98 GC Coolant loss from bottom hose at the engine mount  (Read 9294 times)

0 Members and 1 Guest are viewing this topic.

RockingDad

  • Guest
98 GC Coolant loss from bottom hose at the engine mount
« on: February 11, 2008, 10:41:24 AM »
Morning everyone, Tow bar on now, but sprung a coolant leak.

It seems to be running down the bottom coolant hose and dropping off onto the cowling under it. Has anyone else had this?

I'm thinking it could just be a poor seal around the engine mount part of this hose but rang a local jeep parts place and the hose is £58!!!

I'm thinking about seeing if a jubilee clip instead of the spring clip will cure it but if not and I have to change the hose has anyone any tips about the easiest wasy to do it? Theres not a lot of room at the top mount there!

Cheers

RockingDad
Logged

tim_aka_tim

  • Club Member
  • Guru
  • *
  • Guru: 1
  • Offline Offline
  • Posts: 4464
  • Vehicle: Honda Pilot
  • Year: 2008
  • Regional Organiser North America
(No subject)
« Reply #1 on: February 11, 2008, 11:21:45 AM »
Yep, those hoses cost a bomb. They're shaped and have springs inside to stop them deforming. Halfords do various width and length hoses with spring reinforcement, and they ain't 58 quid!
Logged

RockingDad

  • Guest
(No subject)
« Reply #2 on: February 11, 2008, 03:22:30 PM »
hmmm....might not be the hose. I've been advised there is a weep hole in the casing of the water pump that will leak fluid when the inner seals fail. going to check this out later. Can anyone advise what problems I need to look out for removing the pump. there seems to be a lot of kit to remove to take it out etc.

Cheers

Mark
Logged

daggie

  • Moderator
  • Guru
  • *
  • Guru: 3
  • Offline Offline
  • Posts: 3447
(No subject)
« Reply #3 on: February 11, 2008, 06:18:50 PM »
waterpump
Logged
Grand cherry, 3.0 crd Overland
Grand cherry, 2.7 crd
95, Cherry, aka Blackie      P38 range rover

RockingDad

  • Guest
(No subject)
« Reply #4 on: February 11, 2008, 07:29:02 PM »
Quote from: "daggie"
waterpump


Why so sure????   :?:
Logged

tim_aka_tim

  • Club Member
  • Guru
  • *
  • Guru: 1
  • Offline Offline
  • Posts: 4464
  • Vehicle: Honda Pilot
  • Year: 2008
  • Regional Organiser North America
(No subject)
« Reply #5 on: February 11, 2008, 08:33:21 PM »
We've all had one go on us at some point.
Logged

daggie

  • Moderator
  • Guru
  • *
  • Guru: 3
  • Offline Offline
  • Posts: 3447
(No subject)
« Reply #6 on: February 11, 2008, 09:28:18 PM »
:grinyes:
Logged
Grand cherry, 3.0 crd Overland
Grand cherry, 2.7 crd
95, Cherry, aka Blackie      P38 range rover

greggmo

  • Founder
  • Guru
  • *
  • Guru: 2
  • Offline Offline
  • Posts: 8230
(No subject)
« Reply #7 on: February 11, 2008, 10:24:50 PM »
try the hose clips first  but it does sound like the water pump is on its way out maybe. not too bad a job mate. 8-)
Logged

The Smiths

  • Guru
  • *
  • Guru: 1
  • Offline Offline
  • Posts: 1084
(No subject)
« Reply #8 on: February 11, 2008, 11:10:55 PM »
Change the waterpump before it collapses and fries your engine :-)
Logged
If you always do what you have always done You will always get what you have always got
Please give to our Mac4x4 fund: http://www.justgiving.com/The-Smiths-2015

RockingDad

  • Guest
(No subject)
« Reply #9 on: February 12, 2008, 12:29:55 AM »
Quote from: "The Smiths"
Change the waterpump before it collapses and fries your engine :shock:
Logged

greggmo

  • Founder
  • Guru
  • *
  • Guru: 2
  • Offline Offline
  • Posts: 8230
(No subject)
« Reply #10 on: February 12, 2008, 09:21:10 PM »
its only ever gonna fry your engine if you let it over heat but this should never happen in a motor with a temp gage...unless ya cant read one that is :roll:
Logged

Lornaben

  • Lord of the Mindy ring
  • Guru
  • *
  • Guru: 2
  • Offline Offline
  • Posts: 3026
  • Vehicle: CJ3B (Mindy)
    • Mahindra Register
(No subject)
« Reply #11 on: February 12, 2008, 10:18:49 PM »
Quote from: "greggmo"
its only ever gonna fry your engine if you let it over heat but this should never happen in a motor with a temp gage...unless ya cant read one that is :oops:
Logged

Bubba

  • "Cooter"
  • Marshal
  • Guru
  • *
  • Guru: 69
  • Offline Offline
  • Posts: 21029
(No subject)
« Reply #12 on: February 12, 2008, 10:51:39 PM »
wife in yer ear bla blaa bla blaa kids are we there yet are there yet are we there yet are we there yet are we there yet are we there yet
Logged


trucks


shedric
cletus
mr whippy

I spent most of my money on alcohol, women and old  iron........ the rest of it I just wasted.

RockingDad

  • Guest
(No subject)
« Reply #13 on: February 13, 2008, 12:52:51 PM »
LMAO!!!   :lol:

Haven't got time to do it myself so booked it into Mansfields 4X4 at Manningtree to sort it.

On a plus note....nearly finished bracket fabrication for my side bars and just picked up bull bars

Cheers

RD
Logged

RockingDad

  • Guest
(No subject)
« Reply #14 on: February 18, 2008, 03:13:57 PM »
Afternoon all,

Just n case any was wondering, was the water pump, bearings and seals had gone. Changed over today by the friendly chaps at Mansfields 4X4 Jeep in Manningtree. No more wazzing on the drive for my Jeep!!!!

 :-D   :-D
Logged

greggmo

  • Founder
  • Guru
  • *
  • Guru: 2
  • Offline Offline
  • Posts: 8230
(No subject)
« Reply #15 on: February 18, 2008, 08:09:24 PM »
sorted. 8-)
Logged

daggie

  • Moderator
  • Guru
  • *
  • Guru: 3
  • Offline Offline
  • Posts: 3447
(No subject)
« Reply #16 on: February 19, 2008, 05:52:59 PM »
cool 8-)
Logged
Grand cherry, 3.0 crd Overland
Grand cherry, 2.7 crd
95, Cherry, aka Blackie      P38 range rover
Pages: [1]   Go Up
« previous next »
 
Powered by EzPortal